Accurate Fuel Monitoring
The FL-2 offers pilots digital fuel levels, with unprecedented accuracy, for dual fuel tanks. Not only does the FL-2 display each tank digitally, it also provides 90′ graphical arcs for immediate, quick reference of each tank’s level. The FL-2 can be ordered to work with resistive probes (FL-2R-12 or FL-2R-24, depending on 12 or 24 volts), capacitive probes (FL-2CA) or 0-5 volt output, (such as with some Skysports probes (FL-2V). Please be sure to specify which model you need when you order your FL-2.
The FL-2 is not STC’d for installation in a certified aircraft.
210 Degree, analog arc with green, yellow and red LED’s.
Large, crisp, LCD display with adjustable backlighting for night operations.
The FL-2 can be modified for $98 to output data to Electronics International’s MUX-8A. This allows pilots to review critical system information for flights.
Fuel Slosh Stabilization
When in flight, fuel will slosh around in the aircraft fuel tanks, creating irritating readings that constantly jump around. The FL-2 has a Fuel Slosh Stabilization calibration point that averages fuel level readings, creating a much more stable, but still extremely accurate fuel reading. Calibrate between a couple of seconds all the way up to over a minute of fuel slosh averaging.
9 Calibration Points
The FL-2 allows installers to program from as little as two all the way up to nine fuel level calibration points in the fuel tank. This flexibility eliminates inaccuracies due to non-linear fuel tanks.
Easy Programming Interface
The FL-2 is a simple instrument to install and program. Clear step-by-step instructions make programming the instrument easy to calibrate to your fuel tank senders.
The pilot can easily select between displaying fuel level in Liters, Gallons or Lbs with a switch on the front of the instrument panel.
FL-2 KIT DETAILS
Instrument, Wire Harness, Installation and Operating Instructions.
Stocked Item (Specify FL-2RA-12, FL-2RA-24, FL-2CA or FL-2V when ordering).
2.5″ x 2.5″ x 3.65″ Depth, 2.25″ Bezel
Two sets of 7 High Intensity Light Emitting Diodes (LEDs) in 90 degree arcs with Intensity Control Line available for dimming. Sequential flash test on power up.
7.5 to 35 volts, 1/10 Amp.
1/4 Tank Warning
If the left or right tank level reaches 1/4 of a tank, the appropriate yellow LED will blink.
If the left or right tank reaches 1/8 of a tank, the appropriate red LED will blink.
If the wire to the left or right fuel tank sensor becomes open, the analog display for the tank with the problem will show an empty and the digital display will show “OPEN.”
To acknowledge a blinking LED (i.e., to stop the blinking), change the position of the Tank Selector Switch.
Max, Min and Resolution
Minimum fuel level for each tank: 4 gallons. Maximum fuel level for each tank: 999 gallons. Resolution: Programmable to 1 or 1/2 Gallon (Fuel levels below 2 gallons will be displayed as “0”).
External Warning Control Line
Grounds when any Red Warning LED is on or yellow LED is blinking. Current should be limited to 1/10 amp.
7.5 to 35 volts, 1/10 Amp.
Independent control lines allow pilots to adjust the intensity of both the Green Indicator Lights and the LCD Backlight during instrument operations.
Fuel Probe Overview
The FL-2 and FL-1 can be ordered to work with resistive probes, capacitive probes (FL-2CA or FL-1CA) or 0-5 volt output (such as with some Skysports probes (FL-2V or FL-1CA).
Electronics International manufactures the P-300C Capacitive Fuel Probe for use with any FL-2CA or FL-1CA instrument. Our newer P-300C-Mini Probe offers more flexibility for installations requiring bending or thinner probes.
3/4″ O.D. Pipe with 3/4″ NPT Boss
Specify length when ordering (between six inches to twenty feet long). Although ordering correct lengths is recommended, you may also cut the probes to length. Call EI for cutting instructions before attempting to shorten your probes.
Please allow 2-3 weeks for your order to ship.
5v square wave
3/16″ SS Tubing with a 1/8″ or 1/4″ (Specify when ordering) NPT fitting.
Specify length when ordering (between two inches to six feet long). Although ordering correct lengths is recommended, you may also cut the probes to length. Call EI for cutting instructions before attempting to shorten your probes.
Unlike the standard P-300C, this probe can be bent to fit into your non-linear tank.
3+ weeks for your order to ship.
5v square wave